Corsair

Corsair Vengeance LPX 16GB DDR4-3200 CL16

F
Ranked #14 in RAM
140 LP on the category ladder what's LP?

A plain, low-profile DDR4 kit that ran its rated profile without stability problems in PCMENA's test, but it offers 16GB of DDR4-3200 for older DDR4 boards and cannot move to a DDR5 platform such as AMD's AM5.

Consolidated from 2 independent outlets

See the sources
Flagged as a product to avoid

2 of 7 research runs entered this as a product to avoid rather than a pick.

Underperforms in bandwidth compared to newer DDR4-3600 kits, and its price is higher than necessary.

Flagged 13 September 2026

1 earlier flag predates the point where runs began recording their reasoning, so its grounds were never written down.

Why the boards include products to avoid

Check price

About this product

This page covers the Corsair Vengeance LPX CMK16GX4M2B3200C16, a 16GB DDR4 desktop memory kit made of two 8GB sticks with black anodized aluminum heat spreaders and no lighting. It boots at 2133MHz and reaches its rated 3200MHz at 16-18-18-36 and 1.35V once you enable its XMP 2.0 profile in the BIOS.

It is DDR4 memory, and Corsair lists it for Intel 200 to 600 series and X299 boards and AMD 300, 400 and 500 series boards. It will not work in a DDR5 system such as AMD's AM5 platform. At 33.53mm tall it is a low-profile kit, which Corsair pitches at small cases and builds where internal space is tight.

Evidence on this exact kit is thin. PCMENA published a short hands-on review of this part number, and HEXUS tested the four-stick 16GB version (4x4GB) with the same 16-18-18-36 and 1.35V profile. Corsair also notes that kits sharing this part number can be built with different memory chips.

Specifications

Pros & cons

  • ✓ Low 33.53mm modules suit small cases and tight cooler clearances
  • ✓ One XMP 2.0 setting in the BIOS takes it to its rated 3200MHz
  • ✓ Stable under heavy loads in PCMENA's hands-on test
  • ✓ Lifetime limited warranty
  • ✗ DDR4 only, and Corsair's compatibility list stops at Intel 600 series and AMD 500 series boards
  • ✗ Runs at only 2133MHz until you enable XMP in the BIOS
  • ✗ The memory chips inside can be Micron, Samsung or Hynix under the same part number
  • ✗ Going past its rated speed needed extra BIOS tuning in PCMENA's test

The sources behind this ranking

We searched the web and YouTube for what has been published about this product, then read the articles, video transcripts and comments we found.

Evidence 1 article and 1 video review

Frequently asked questions

It ranks #14 of 15 on our RAM tier list, in F tier. That placement draws on 2 independent outlets.

No. It is a DDR4 kit, and Corsair lists Intel 200 to 600 series and X299 boards and AMD 300, 400 and 500 series boards for it. AMD's AM5 platform uses DDR5 exclusively, so a new AM5 build needs DDR5 memory instead.

Very likely. Corsair lists the Vengeance LPX at 33.53mm tall and describes its small form factor as ideal for smaller cases or any system where internal space is at a premium.

Yes, one. The kit boots at 2133MHz with 15-15-15-36 timings. Enable its XMP 2.0 profile in the BIOS to reach 3200MHz at 16-18-18-36 and 1.35V. PCMENA and HEXUS both describe that single step as all the setup the memory needed.

Not always. Corsair says kits can be built with different memory chips even when they share a part number. The version number on the sticker tells you which: V3 means Micron, V4 means Samsung and V5 means Hynix.

Possibly, with work. Corsair designs the Vengeance LPX for overclocking with individually screened chips, but notes that maximum speed depends on the motherboard and CPU. PCMENA found that pushing beyond the rated speed needed more fine-tuning in the BIOS.

Ranked nearby in RAM